+44 (0)1903 788287
Filtered (86)
  • Encoder Technology 15T Through Hollow shaft encoder

    Encoder Technology 15H Blind Hollow Shaft Incremental Encoder

    Features

    • Very high-performance economical encoder
    • Low profile—25.4 mm height and 38 mm diameter
    • Thru-bore with sizes up to 10 mm
    • Simple, innovative flex mounting system (Global Mounting Standards)
    • Up to 12 pole commutation optional for brushless motor control
    Details
  • Encoder Technology 15T Through Hollow shaft encoder

    Encoder Technology 15T Through Hollow Shaft Incremental Encoder

    Features

    • Very high-performance economical encoder
    • Low profile—25.4 mm height and 38 mm diameter
    • Thru-bore with sizes up to 10 mm
    • Simple, innovative flex mounting system (Global Mounting Standards)
    • Up to 12 pole commutation optional for brushless motor control
    Details
  • Encoder Technology 25T Through Hollow Shaft Incremental Encoder

    Encoder Technology 25T Through Hollow Shaft Incremental Encoder

    Features

    • 5mm Opto-ASIC encoder with a low profile (50.8mm)
    • Imperial bore sizes range from 0.625” to 1.125”
    • Metric bore sizes ranging from 6 mm to 28 mm
    • Single replacement solution for 50.8mm to 88.9mm encoders
    • Resolutions to 10,000 PPR, frequencies to 1 MHz
    • Versatile flexible mounting options
    • RoHS compliant
    • Corrosion-Resistant Option
    Details
  • Encoder Technology 260 Through hollow shaft Incremental encoder

    Encoder Technology 260 Through Hollow Shaft Incremental Encoder

    Features

    • Low profile 30.3mm
    • Up to 12 pole commutation
    • Thru-bore and hollow-bore (blind) styles
    • Simple, innovative flexible mounting system
    • Incorporates Opto-ASIC technology
    Details
  • Encoder Technology 75HA Through HolIow Shaft Incremental Encoder

    Encoder Technology 75HA Through Hollow Shaft Incremental Encoder

    Features

    • Body: Precision Machined Aluminium
    • Cover: Precision Machined Aluminium (Powder Coated)
    • Shaft: Stainless Steel
    • Bearings: Ballraces
    • Shaft Sealing: Front: Sealed bearing - Rear: Single lip seal on the rear of cover
    • Protection: IP65
    • Operating Temp: -20 to +60°C (Higher on request)
    • Maximum Speed: 3000 RPM (Higher on request)
    • Torque: 2Ncm (typical)
    • Inertia: 100gcm2 (typical)
    • Shaft Loading: Designed to support its weight
    • Cable: Screened, oil and salt waterproof
    • Impulse Frequency: Up to 300KHz (depending on model)
    • Current Consumption: 60mA (typical – without load)
    Details
  • Encoder Technology 75HS-Hollow shaft incremental Encoder

    Encoder Technology 75HS Through Hollow Shaft Incremental Encoder

    Features

    • Body: Stainless Steel (316)
    • Cover: Stainless Steel (316)
    • Shaft: Stainless Steel
    • Bearings: Ballraces
    • Shaft Sealing: Front: Sealed bearing + Single lip seal
    • Rear: Single lip seal on the rear of the cover
    • Protection: (IP66 / IP67)
    • Operating Temp: -20 to +60°C (Higher on request)
    • Maximum Speed: 3000 RPM
    • Torque: 4Ncm (typical)
    • Inertia: 200gcm2 (typical)
    • Shaft Loading: Designed to support its weight
    • Cable: Screened, oil and salt waterproof
    • Impulse Frequency: Up to 300KHz (depending on model)
    • Current Consumption: 60mA (typical – without load)
    Details
  • Encoder Technology 760 Through Hollow Shaft Incremental Encoder

    Encoder Technology 760 Through Hollow Shaft Incremental Encoder

    Features

    • Size 25 / 63.5mm Diameter (Hollow Shaft)
    • Up to 12 Pole Commutation Available
    • Thru Bore and Blind Bore Options
    • Simple, Innovative Flexible Mounting System
    • Incorporates Opto-ASIC Technology
     
    Details
  • Encoder Technology 775 Through Hollow Shaft Incremental Encoder

    Encoder Technology 775 Through Hollow Shaft Incremental Encoder

    Features

    • Thru-bore design for easy mounting
    • Bore options to 1.375" and 32mm
    • Incorporates Opto-ASIC technology
    • Resolutions to 4096 PPR
    • 100° C operating temperature available
    Details
  • Encoder Technology 776 Through Hollow Shaft Incremental Encoder

    Encoder Technology 776 Through Hollow Shaft Incremental Encoder

    Features

    • Slim profile—only 34.5mm in depth
    • Thru-bore design for easy mounting
    • Incorporates Opto-ASIC technology
    • Resolutions to 4096 PPR
    • Bore options to 1.875" and 43mm
    Details
  • Encoder Technology 90HA Through Hollow Shaft Incremental Encoder

    Encoder Technology 90HA Through Hollow Shaft Incremental Encoder

    Features

    • Body: Precision Machined Aluminium
    • Cover: Precision Machined Aluminium (Powder Coated)
    • Shaft: Stainless Steel
    • Bearings: Ballraces
    • Shaft Sealing: Front: Sealed bearing
    • Rear: Single lip seal on the rear of the cover
    • Protection: IP65
    • Operating Temp: -20 to +60°C (Higher on request)
    • Maximum Speed: 3000 RPM (Higher on request)
    • Torque: 3Ncm (typical)
    • Inertia: 600gcm2 (typical)
    • Shaft Loading: Designed to support its weight
    • Cable: Screened, oil and salt waterproof
    • Impulse Frequency: Up to 300KHz (depending on model)
    • Current Consumption: 60mA (typical – without load)
    Details
  • Encoder Technology A102H Large Bore Encoder

    Encoder Technology A102H Large Bore Through Hollow Shaft Encoder

    Features

    • Number of output pulses per revolution 5.000 - 500.000 ppr
    • Line number on disc (z) 5.000
    • Maximum shaft speed 8000 rpm
    • The permissible motion of the shaft - axial: ± 1.00 mm - radial: 0.02 mm
    • Accuracy (T1-period lines on disc in arc. sec) ± 0.05T1 arc. sec
    • Starting torque at 20°C ≤ 0.01 Nm
    • Rotor moment of inertia < 20x10-4 kgm2
    • Protection (housing) (IEC 529) IP64
    • Protection (shaft side) (IEC 529) IP64
    • Maximum weight without cable 0.8 kg
    • Operating temperature -20...+70°C
    • Storage temperature -30...+85°C
    • Maximum humidity (non-condensing) 98%
    • Permissible vibration (55 to 2000 Hz) ≤ 100 m/s²
    • Permissible shock (11 ms) ≤ 300m/s²
    Details
  • Encoder Technology A58HE1 Through Hollow Shaft Incremental Encoder

    Encoder Technology A58HE1 Through Hollow Shaft Incremental Encoder

    Features

    • Number of output pulses per revolution 100-108000 ppr
    • Maximum shaft speed 10000 rpm
    • The permissible motion of the shaft - axial: ± 0.5 mm - radial: ± 0.05 mm
    • Accuracy (T1-period lines on disc in arc. sec) ± 0.1T1 arc. sec
    • Starting torque at 20°C ≤ 0.025 Nm
    • Rotor moment of inertia < 1.5x10-4 kgm2
    • Protection (housing) (IEC 529) IP64
    • Protection (shaft side) (IEC 529) IP64
    • Maximum weight without cable 0.3 kg
    • Operating temperature -10...+70°C
    • Storage temperature -30...+80°C
    • Maximum humidity (non-condensing) 98%
    • Permissible vibration (55 to 2000 Hz) ≤ 100 m/s²
    • Permissible shock (5 ms) ≤ 1000 m/s²
    Details

  • Motrona AX020: Process Indicator for Analog Signals

    Features

    • Scalable 14-bit analog input for 0 ... 10 V or 0/4 ... 20 mA
    • Power supply 24 VDC
    • Miniature norm panel housing
    • 5 digits LED display with 8 mm height
    • Display range -19999 ... 99999, adjustable zero and full-scale value
    • Latch input to freeze the display, minimum/maximum record memory
    • Easy to set up with only two front keys and menu support
    • Delivery includes adapter frame for 50 x 25 mm cut out and label set with dimensions
    • Front dimension 48 x 24 x 59 mm (1.89 x 0.945 x 2.322")
    Details
  • Motrona TouchMatrix AX350 process display

    Motrona AX350: touchMATRIX® Process Indicator with two 16 bit Analog Inputs

    Features

    • 2 universal 16-bit analogue inputs for ±10 V or 0/4 … 20 mA
    • 3 control inputs for HTL / PNP signals
    • Power supply 18 ... 30 VDC
    • 24 V auxiliary output for encoder supply
    • High accuracy reference output 10 V for potentiometers > 1 kOhm
    • 3.78 x 1.89-inch norm panel housing and IP65 protection
    • Bright and high-contrast display with event-dependent color variations
    • Emulation of a 7-segment display inclusively icons and units
    • Intuitive and easy parameterization by plain text and touchscreen
    • Operating modes for visualization of INPUT 1, INPUT 2 or combinations of IN1 + IN2, IN1 - IN2, IN1 x IN2, IN1: IN2
    • Numerous features, e. g. tara, filters, averaging
    • Linearization with 24 control points

    Options

    • Option AC: Power supply 115 ... 230 VAC
    • Option AO: 16-bit analog output, 4 control outputs, serial RS232 interface
    • Option AR: 16-bit analog output, 4 control outputs, serial RS485 interface
    • Option CO: 4 control outputs, serial RS232 interface
    • Option CR: 4 control outputs, serial RS485 interface
    • Option RL: 2 relay outputs
    • Option IO: IO-Link Device V1.1
    Details

  • Motrona AX350/IO: touchMATRIX® IO-Link Indicator

    Features

    • 2 universal 16-bit analog inputs for ±10 V or 0/4 … 20 mA
    • 3 control inputs for HTL / PNP signals
    • Power supply 18 ... 30 VDC
    • 24 V auxiliary output for encoder supply
    • High accuracy reference output 10 V for potentiometers > 1 kOhm
    • 3.78 x 1.89-inch norm panel housing and IP65 protection
    • Bright and high-contrast display with event-dependent color variations
    • Emulation of a 7-segment display inclusively icons and units
    • Intuitive and easy parameterization by plain text and touchscreen
    • Operating modes for visualization of INPUT 1, INPUT 2 or combinations of IN1 + IN2, IN1 - IN2, IN1 x IN2, IN1: IN2
    • Numerous features, e. g. Ttara, filters, averaging
    • Linearization with 24 control points

    Option IO (= IO-Link Device)

    • Data transfer via COM3 (230,4 kBaud)
    • Cycle times < 3 msec
    • Process data IN 32 Byte (6 x process values from AX350): - Analog value 1 (scaled / linearized) and unit - Analog value 2 (scaled / linearized) and unit - Analog value 1 (scaled / linearized) with totalisation and unit - Analog value 2 (scaled / linearized) with totalisation and unit - Shortcut analogue value 1 (scaled / linearized) with analogue value 2  (scaled / linearized) and unit - Shortcut totalisator analogue value 1 (scaled / linearized) with totalisator analogue value 2 (scaled / linearized) and unit
    • Process data Out 8 Byte (2 x IO-Link process values to AX350): - IOL process value Out 1 with scaling, adjustable decimal point and programmable units - IOL process values Out 2 with scaling, adjustable decimal point and programmable units

    Combinable with further options:

    • Option AC: Power supply 115 ... 230 VAC
    • Option AO: 16-bit analog output, 4 control outputs, serial RS232 interface
    • Option AR: 16-bit analog output, 4 control outputs, serial RS485 interface
    • Option CO: 4 control outputs, serial RS232 interface
    • Option CR: 4 control outputs, serial RS485 interface
    • Option RL: 2 relay outputs
    Details

  • Motrona BY701-Firmware: Synchronization of Drives

    Features

    • MC700 is a universal motion controller for 1 to 4 axes, which can be assigned any motion control functions by loading firmware. Together with the firmware BY701 (see firmware), this controller offers excellent synchronous functions for 1 - 4 axes.
    • The firmware offers all conceivable possibilities for the synchronization of drives, including the influence of phase position and the relative position between the drives and numerous index and print mark functions.
    • Optionally, a "physical master" or the built-in "virtual master axis" with programmable speeds and ramps can be used as the master drive.
    • The number of successive axes can be extended arbitrarily via a cascading output.
    • MC700 controllers can be operated via an external control terminal, serial interface or optional via CANBUS (MC700/CI). PC operator software is included.
    • PROFIBUS connection possible via gateway PB251 (see accessories)
    Details

  • Motrona CA306: Simple Preset Unit for CAN-Bus

    Features

    • Power supply 10 ... 30 VDC
    • Compact norm panel housing
    • Preset range: 6 digits or 5 digits with sign
    • DIL-switch for set up of the transmission parameters
    • Dimension H x B x T = 96 x 48 x 140 mm (3.78 x 1.89 x 5.51 ")
    Details

  • Motrona CA340: Fieldbus Indicator for CAN-Bus (SDO and PDO)

    Features

    •  Power supply 10 ... 30 VDC
    • Compact norm panel housing
    • 6 digits LED display with 15 mm height
    • Display range -199999 ... 999999
    • DIL-switch for setup of the transmission parameters
    • Dimension H x B x T = 96 x 48 x 140 mm (3.78 x 1.89 x 5.12 ")
    Details

  • Motrona DM350: touchMATRIX® Strain Gauge Indicator for force sensors (full bridge)

    Features

    • Strain gauge input, 6-wire connection
    • Input pt100 and thermocouples (J and K)
    • 3 control inputs for HTL / PNP signals
    • Power supply 18 ... 30 VDC
    • Adjustable bridge voltage 3 VDC to 10 VDC
    • 1 … 10 mV sensitivity
    • Standard installation housing with 96 x 48 mm and protection class IP65
    • Bright and high-contrast graphic display with event-dependent color variants
    • Emulation of a 7-segment display with symbols and units
    • Intuitive and simple parameterization through plain text and touchscreen
    • Numerous functions such as tare, filter, averaging
    • Linearization with 24 support points

    Options

    • Option AC: Power supply 115 ... 230 VAC
    • Option AO: 16-bit analog output, 4 control outputs, serial RS232 interface
    • Option AR: 16-bit analog output, 4 control outputs, serial RS485 interface
    • Option CO: 4 control outputs, serial RS232 interface
    • Option CR: 4 control outputs, serial RS485 interface
    • Option RL: 2 relay outputs
    • Option IO: IO-Link Device V1.1
    Options can be combined.
    Details

  • Motrona DP350: touchMATRIX® Indicator for transonic distance measurement

    Features

    • Start-stop interface for absolute transducers and magnetostrictive sensors
    • Adjustable frequency of the init pulses from 62.5 Hz to 5 kHz
    • 3 control inputs for HTL / PNP signals
    • Power supply 18 ... 30 VDC
    • Auxiliary voltage output 24 VDC or 5 VDC for encoder supply
    • 8-decade LCD display (colour: red, green, yellow)
    • Resistive touchscreen
    • Standard housing with 96 x 48 mm and IP65 protection
    • Intuitive and easy parameterization by plain text and touchscreen
    • Numerous functions such as scaling, filter, zero offset, counting direction etc.
    • Linearization with 24 interpolation points

    Options

    • Option AC: Power supply 115 ... 230 VAC
    • Option AO: 16-bit analog output, 4 control outputs, serial RS232 interface
    • Option AR: 16-bit analog output, 4 control outputs, serial RS485 interface
    • Option CO: 4 control outputs, serial RS232 interface
    • Option CR: 4 control outputs, serial RS485 interface
    • Option RL: 2 relay outputs
    Options can be combined.
    Details

  • Motrona DX020: Small-sized Tachometer and Frequency Counter

    Features

    • Single channel pulse input [HTL]
    • Input frequency up to 20 kHz
    • Programmable input filter for mechanical input contacts
    • Power supply 24 VDC
    • Miniature norm panel housing
    • 6 digits LED display with 8 mm height
    • Display range  -199999 ... 999999
    • Dimension B x H x T = 48 x 24 x 59 mm (1.89 x 0.94 x 2.32 ")
    Details

  • Motrona DX350: touchMATRIX® Digital Indicator (HTL)

    Features

    • Pulse input with format A, B, 90° [HTL], single channel as an option
    • HTL inputs for encoder and sensors with NPN / PNP or NAMUR switching characteristics
    • Input frequency up to 250 kHz
    • 3 control inputs for HTL / PNP signals
    • Power supply 18 ... 30 VDC
    • 24 V auxiliary output for encoder supply
    • 3.78 x 1.89-inch norm panel housing and IP65 protection
    • Bright and high-contrast display with event-dependent color variations
    • Emulation of a 7-segment display inclusively icons and units
    • Intuitive and easy parameterization by plain text and touchscreen
    • Multi-functional device for speed, position, timer, counter or velocity application
    • Operating modes such as scaling, average filter, start-up suppression
    • Linearization with 24 control points

    Options

    • Option AC: Power supply 115 ... 230 VAC
    • Option AO: 16-bit analog output, 4 control outputs, serial RS232 interface
    • Option AR: 16-bit analog output, 4 control outputs, serial RS485 interface
    • Option CO: 4 control outputs, serial RS232 interface
    • Option CR: 4 control outputs, serial RS485 interface
    • Option RL: 2 relay outputs
    Options can be combined.
    Details

  • Motrona DX355: touchMATRIX® Graphic Display (HTL / RS422)

    Features

    • 2 Incremental inputs with format A, /A, B, /B
    • Differential, single-ended HTL / RS422
    • Input frequency up to 1 MHz
    • Power supply 18 ... 30 VDC
    • 5 / 24 VDC auxiliary output for encoder supply
    • 3.78 x 1.89-inch norm panel housing and IP65 protection
    • Bright and high-contrast display with event-dependent color variations
    • Emulation of a 7-segment display inclusively icons and units
    • Intuitive and easy parameterization by plain text and touchscreen
    • Multi-functional device for speed, process time, timer, counter or velocity application
    • Operating modes such as scaling, average filter, start-up suppression
    • Linearization with 24 control points

    Options

    • Option AC: Power supply 115 ... 230 VAC
    • Option AO: 16-bit analog output, 4 control outputs, serial RS232 interface
    • Option AR: 16-bit analog output, 4 control outputs, serial RS485 interface
    • Option CO: 4 control outputs, serial RS232 interface
    • Option CR: 4 control outputs, serial RS485 interface
    • Option RL: 2 relay outputsOptions can be combined.
    Details

  • Motrona EC350: touchMATRIX® EtherCAT Indicator

    Features

    • EtherCAT interface
    • 3 control inputs for remote release
    • Power supply 18 ... 30 VDC
    • Norm panel housing with 96 x 48 mm and protection class IP65
    • Bright and high-contrast graphic display with event-dependent color variants
    • Emulation of a 7-segment display with symbols, units and bargraph
    • Intuitive and simple parameterization through plain text and touchscreen
    Details

  • Motrona EN350: touchMATRIX® EtherNET/IP Indicator

    Features

    • EtherNET/IP interface
    • 3 control inputs for remote release
    • Power supply 18 ... 30 VDC
    • Norm panel housing with 96 x 48 mm and protection class IP65
    • Bright and high-contrast graphic display with event-dependent color variants
    • Emulation of a 7-segment display with symbols, units and bargraph
    • Intuitive and simple parameterization through plain text and touchscreen
    Details

Title

Company reg # : 4359149
VAT Reg #: 860 5449 17

Copyright © 2018 Encoder Technology Ltd. All Rights Reserved.
Go to Top