+44 (0)1903 788287
Filtered (6)

  • CT701-Firmware: Eccentric Material Processing

    Features

    • MC700 is a universal motion controller for 1 to 4 axis, programmable for multiple motion applications by simple download of the corresponding function firmware
    • With the use of Matona's CT701 firmware, this unit provides excellent solutions with all kinds of guillotine cutters and rotary eccentric shears needing a cosine-compensated speed profile during the penetration of the tool
    • Extremely smooth motion  to protect  mechanical solution, by self-optimizing polynomial speed transitions
    • High cutting accuracy, even during line acceleration and at high speeds
    • Programmable cosine-compensated speed profile
    • Special torque control features to master the impact load when cutting hard materials like stainless steel etc.
    • Special profile features to avoid deadlock between tool and material
    • Embedded virtual master axis (selectable)
    • Black-box unit for cabinet mounting
    • Remote control and communication facilities via external operator terminal, serial PC communication, PROFIBUS or optional via CANBUS (MC700/CI) etc.
    Details

  • CT803-Firmware: Rotating Cross Cutters

    Features

    • 2 pulse inputs with format  A, /A, B, /B, Z, /Z [HTL, RS422]
    • With an input frequency of up to 2 MHz
    • 2 control inputs with format  SIN+, SIN-, COS+, COS- [1 Vss] with an input frequency of up to 400 kHz
    • 2 SSI inputs with format  DATA+, DATA-, CLOCK+, CLOCK- up to 25 Bit, with SSI switching frequency of 100 Hz ... 1 MHz
    • 2 scalable 14-bit analog inputs for ±10 V or 0/4 ... 20 mA
    • 4 control inputs for PNP / NPN signals [10 ... 30 VDC]
    • 4 fast interrupt inputs for PNP / NPN signals [10 ... 30 VDC]
    • 1 pulse output with format  A, /A, B, /B, Z, /Z [RS422]
    • 4 control outputs with push-pull characteristic, short-circuit-proof [5 ... 30 VDC]
    • 2 scalable 14-bit analog outputs for ±10 V or 0/4 ... 20 mA
    • Loop time approx. 250 µs
    • Power supply 18 ... 35 VDC
    • Snap-on housing for top-hat rail (according to EN 60715)
    • OnBoard interfaces: Ethernet / IP, RS232 / RS485, USB 2.0, CANopen, Modbus RTU
    • Optional Ethernet interfaces: EtherCAT, Ethernet / IP, Modbus TCP, Powerlink, PROFINET, SERCOS III
    • Optional Fieldbus interfaces (slave): CC-Link, DeviceNet, PROFIBUS
    • Operates with all 4-Q-drive systems, equipped with a standardized drive communication bus (e. g. SERCOS-II). Alternatively, ±10 V setpoint can be used
    • The controllers can be setup by an external operator terminal as well as HMI’s via standardized factory communication bus e.g. PROFINET
    • Setup via Windows operator software (free of charge)
    Details

  • Motrona BY701-Firmware: Synchronization of Drives

    Features

    • MC700 is a universal motion controller for 1 to 4 axes, which can be assigned any motion control functions by loading firmware. Together with the firmware BY701 (see firmware), this controller offers excellent synchronous functions for 1 - 4 axes.
    • The firmware offers all conceivable possibilities for the synchronization of drives, including the influence of phase position and the relative position between the drives and numerous index and print mark functions.
    • Optionally, a "physical master" or the built-in "virtual master axis" with programmable speeds and ramps can be used as the master drive.
    • The number of successive axes can be extended arbitrarily via a cascading output.
    • MC700 controllers can be operated via an external control terminal, serial interface or optional via CANBUS (MC700/CI). PC operator software is included.
    • PROFIBUS connection possible via gateway PB251 (see accessories)
    Details

  • Motrona DM221: Strain Gauge Amplifier >>> Analog

    Features

    • 6-wire connection for one strain gauge full bridge sensor
    • 4 control inputs [HTL/PNP]
    • 1 analog output ±10 V, 0/4 ... 20 mA, 16 bit
    • 4 control outputs for signalling different operation states
    • Power supply 18 ... 30 VDC
    • Functions for scaling and linking the sensor signals (e.g. A+B, A-B, ...)
    • Adjustable bridge voltage per sensor from 3 VDC ... 10 VDC
    • Sensitivity of the sensor inputs 1 ... 10 mV
    • Transmission of the sensor data via RS485
    • Programming via USB and the user interface OS (freeware)
    • Protection class IP20
    • Compact housing for mounting on 35 mm top-hat rail (according to EN 60715)
    Details

  • Motrona DM222: 2 channel Strain Gauge Amplifier >>> Analog

    Features

    • 6-wire connection for two independent strain gauge full bridge sensors
    • 4 control inputs [HTL/PNP]
    • 2 independent analog outputs ±10 V, 0/4 ... 20 mA, 16 bit
    • 4 control outputs for signalling different operation states
    • Power supply 18 ... 30 VDC
    • Functions for scaling and linking the sensor signals (e.g. A+B, A-B, ...)
    • Adjustable bridge voltage per sensor from 3 VDC ... 10 VDC
    • Sensitivity of the sensor inputs 1 ... 10 mV
    • Transmission of the sensor data via RS485
    • Programming via USB and the user interface OS (freeware)
    • Protection class IP20
    • Compact housing for mounting on 35 mm top-hat rail (according to EN 60715)
    Details

  • Motrona IO221: Signal Converter Strain gauge >>> IO-Link

    Features

    • 1 Strain gauge input
    • 3 VDC and 10 VDC bridge voltage per sensor connection
    • 1 … 10 mV sensitivity
    • optionally 3 control inputs for PNP signals [10 ... 30 VDC]
    • IO link interface
    • Power supply 12 ... 30 VDC
    • Compact housing for mounting on 35 mm DIN rail (according to EN 60715)
    Details

Title

Company reg # : 4359149
VAT Reg #: 860 5449 17

Copyright © 2018 Encoder Technology Ltd. All Rights Reserved.
Go to Top