+44 (0)1903 788287
Filtered (17)

  • CT701-Firmware: Eccentric Material Processing

    Features

    • MC700 is a universal motion controller for 1 to 4 axis, programmable for multiple motion applications by simple download of the corresponding function firmware
    • With the use of Matona's CT701 firmware, this unit provides excellent solutions with all kinds of guillotine cutters and rotary eccentric shears needing a cosine-compensated speed profile during the penetration of the tool
    • Extremely smooth motion  to protect  mechanical solution, by self-optimizing polynomial speed transitions
    • High cutting accuracy, even during line acceleration and at high speeds
    • Programmable cosine-compensated speed profile
    • Special torque control features to master the impact load when cutting hard materials like stainless steel etc.
    • Special profile features to avoid deadlock between tool and material
    • Embedded virtual master axis (selectable)
    • Black-box unit for cabinet mounting
    • Remote control and communication facilities via external operator terminal, serial PC communication, PROFIBUS or optional via CANBUS (MC700/CI) etc.
    Details

  • CT803-Firmware: Rotating Cross Cutters

    Features

    • 2 pulse inputs with format  A, /A, B, /B, Z, /Z [HTL, RS422]
    • With an input frequency of up to 2 MHz
    • 2 control inputs with format  SIN+, SIN-, COS+, COS- [1 Vss] with an input frequency of up to 400 kHz
    • 2 SSI inputs with format  DATA+, DATA-, CLOCK+, CLOCK- up to 25 Bit, with SSI switching frequency of 100 Hz ... 1 MHz
    • 2 scalable 14-bit analog inputs for ±10 V or 0/4 ... 20 mA
    • 4 control inputs for PNP / NPN signals [10 ... 30 VDC]
    • 4 fast interrupt inputs for PNP / NPN signals [10 ... 30 VDC]
    • 1 pulse output with format  A, /A, B, /B, Z, /Z [RS422]
    • 4 control outputs with push-pull characteristic, short-circuit-proof [5 ... 30 VDC]
    • 2 scalable 14-bit analog outputs for ±10 V or 0/4 ... 20 mA
    • Loop time approx. 250 µs
    • Power supply 18 ... 35 VDC
    • Snap-on housing for top-hat rail (according to EN 60715)
    • OnBoard interfaces: Ethernet / IP, RS232 / RS485, USB 2.0, CANopen, Modbus RTU
    • Optional Ethernet interfaces: EtherCAT, Ethernet / IP, Modbus TCP, Powerlink, PROFINET, SERCOS III
    • Optional Fieldbus interfaces (slave): CC-Link, DeviceNet, PROFIBUS
    • Operates with all 4-Q-drive systems, equipped with a standardized drive communication bus (e. g. SERCOS-II). Alternatively, ±10 V setpoint can be used
    • The controllers can be setup by an external operator terminal as well as HMI’s via standardized factory communication bus e.g. PROFINET
    • Setup via Windows operator software (free of charge)
    Details
  • Encoder Technology 925 Single Turn Standard Shaft Absoulte Encoder

    Encoder Technology 925 Single Turn Standard Shaft Absolute Encoder

    Features

    • Standard Size 25 package (2.5")
    • Resolutions up to 12-bit (4096 counts)
    • Incorporates Opto-ASIC technology
    • Industrial-grade, heavy-duty housing
    • Optional IP67 seal
    Details
  • Encoder Technology 960 Single Turn Hollow Shaft Absolute Encoder

    Encoder Technology 960 Single Turn Hollow Shaft Absolute Encoder

    Features

    • Low profile—40mm
    • Thru-bore or hollow-bore styles
    • Industrial-grade, heavy-duty housing
    • State-of-the-art Opto-ASIC circuitry
    Details
  • Encoder Technology MA36H Muti-turn Hollowshaft Encoder

    Encoder Technology MA36H

    Features

    • Standard Size 36mm package (1.42")
    • Durable magnetic technology
    • Multiturn absolute encoder (12-bit/39-bit)
    • SSI and CANopen communications
    • Proven new turns counting technology — no gears or batteries
    Details
  • Encoder Technology MA36S Muti-turn Standard Shaft Encoder

    Encoder Technology MA36S Muti-turn Standard Shaft Absolute Encoder

    Features

    • Standard Size 36mm package (1.42")
    • Durable magnetic technology
    • Multiturn absolute encoder (12-bit/39-bit)
    • SSI and CANopen communications
    • Proven new turns counting technology — no gears or batteries
    Details
  • Encoder Technology MA58H Series Multi Turn Hollowshaft Absolute

    Encoder Technology MA58H Series Multi Turn Hollowshaft Absolute Encoder

    Features

    • Multi-Turn Absolute Encoder (14 Bit/39 Bit)
    • SSI and CANopen Communications
    • 58 mm Diameter
    • Durable Magnetic Technology
    • Proven Turns Counting Technology – No Gears or Batteries
    • Retains Absolute Position After a Power Outage
    Details
  • Encoder Technology SA36H Single Turn Hollow Shaft Encoder

    Encoder Technology SA36H Single Turn Hollow Shaft Absolute Encoder

    Features

    • Standard Size 36mm package
    • Durable magnetic technology
    • Up to 14 bits of single-turn resolution
    • SSI and CANopen communications
    • Proven turns counting technology—no gears or batteries
    • Flex mount eliminates couplings and is ideal for motors or shafts
    Details
  • Encoder Technology SA36S Single Turn Standard Shaft Absolut

    Encoder Technology SA36S Single Turn Standard Shaft Absolute Encoder

    Features

    • Standard size 36 mm package (1.42")
    • Durable magnetic technology
    • Up to 14 bits of single-turn resolution
    • SSI and CANopen communications
    • Proven new turns counting technology — no gears or batteries
    Details
  • Encoder Technology SA58H Single Turn Hollow Shaft Absolute Encoder

    Encoder Technology SA58H Single Turn Hollow Shaft Absolute Encoder

    Features

    • Up to 14 Bits of Single-Turn Resolution
    • SSI and CANopen Communications
    • 58 mm Diameter
    • Durable Magnetic Technology
    • Retains Absolute Position After a Power Outage
    Details
  • Encoder Technology TBX36 Standard Shaft Absolute Encoder

    Encoder Technology TBX36 Single Turn Standard Shaft Absolute Encoders

    Features

    • Robust aluminium or stainless steel housing (wall thicknesses up to 5 mm)
    • Stainless steel shaft and ball bearing - ball bearing with Simmer ring
    • Rotor with shaft and permanent magnet mounted in pre-chamber
    • Sensor circuit consisting of ASIC
    • Hall elements and interface electronics in enclosed main chamber
    • Housing protection type IP 69K additionally cast
    • Electrical connection via cable (open cable ends)
    Details
  • Encoder Technology SA36S Single Turn Standard Shaft Absolut

    Encoder Technology TBX42 Single Turn Standard Shaft Absolute Encoder

    Features

    • Interface: SSI
    • Design: 42mm
    • Housing Material: Aluminium, stainless steel
    • Flange & Shaft: Synchroniser flange
    • Resolution: 4096 steps/360°<)
    • Code type: Binary, Gray (optional)
    • Electrical connection: Cable 1m
    • Electrical and/or mechanical variant: Basic version
    Details

  • Encoder Technology TBX50 Single Turn Standard Shaft Absolute Encoder

    Features

    • Robust aluminium or stainless steel housing (wall thicknesses up to 5 mm)
    • Stainless steel shaft and ball bearing - ball bearing with Simmer ring
    • Rotor with shaft and permanent magnet mounted in pre-chamber
    • Sensor circuit consisting of ASIC
    • Hall elements and interface electronics in enclosed main chamber
    • Housing protection type IP 69K additionally cast
    • Electrical connection via cable (open cable ends)
    Details

  • Motrona BY701-Firmware: Synchronization of Drives

    Features

    • MC700 is a universal motion controller for 1 to 4 axes, which can be assigned any motion control functions by loading firmware. Together with the firmware BY701 (see firmware), this controller offers excellent synchronous functions for 1 - 4 axes.
    • The firmware offers all conceivable possibilities for the synchronization of drives, including the influence of phase position and the relative position between the drives and numerous index and print mark functions.
    • Optionally, a "physical master" or the built-in "virtual master axis" with programmable speeds and ramps can be used as the master drive.
    • The number of successive axes can be extended arbitrarily via a cascading output.
    • MC700 controllers can be operated via an external control terminal, serial interface or optional via CANBUS (MC700/CI). PC operator software is included.
    • PROFIBUS connection possible via gateway PB251 (see accessories)
    Details

  • Motrona FM210: Frequency Multiplier / Frequency Divider

    Features

    • Pulse input with format A, B, Z [HTL single-ended, TTL single-ended] or A, /A, B, /B, Z, /Z [RS422, HTL differential]
    • 4 control inputs for HTL, PNP signals [10 ... 30 VDC]
    • Input and output frequency up to 1 MHz
    • 3 incremental outputs with format A, /A, B, /B, Z, /Z, Push-Pull, [8 … 29 VDC]
    • Power supply 9 ... 30 VDC
    • Snap-on housing for top-hat rail (acc. EN 60715)
    • Multiplier/divisor adjustable as quotient F1 / F2
    • Multiplication/division without cumulative residual errors
    • Additional functions such as jog, trim, offset and reference
    Details

  • Motrona FM260: Programmable Pulse and Frequency Multiplier

    Features

    • Pulse input with format A, B, 90° [HTL] or A, /A, B, /B, Z, /Z [RS422]
    • 4 control inputs for PNP signals [10 ... 30 VDC]
    • Input and output frequency up to 1 MHz
    • Pulse output with format A, /A, B, /B, Z, /Z and push-pull characteristic, [5 ... 30 VDC]
    • Power supply 11 ... 30 VDC
    • Snap-on housing for top-hat rail (according to EN 60715)
    • LCD backlighted
    • Setup via keys, RS232
    • The device multiplies an incoming frequency by a proportional factor F1 and a reciprocal factor F2. The two factors F1 and F2 are adjustable in the range of 0.0005 to 9.9999
    • All operation modes provide error-free frequency conversion, with full consideration of the A / B phase and direction of the quadrature signals, therefore no cumulative errors, even with continuous changes of directions and vibrations
    • Zero pulse generator: the frequency multiplier generates at the output an index signal with an adjustable pulse interval, which can be synchronized as needed with the zero pulse at the input
    Details

  • Motrona IT210: Level Converter, Directional Decoder and programmable Pulse Divider

    Features

    • Pulse input in format A, /A, B, /B, Z, /Z [RS422, HTL]
    • Pulse input in format A, B, Z [HTL]
    • Input frequency up to 1 MHz
    • Pulse output in format A, /A, B, /B, Z, /Z [RS422, HTL]
    • Pulse output in format A, B, Z [HTL]
    • Power supply 9 ... 30 VDC
    • Settings via DIL switches
    • Level conversion (RS422, HTL single-ended, HTL differential, TTL and vice versa)
    • Division of two-track A / B pulses with adjustable ratio 1: 1 to 1: 4096
    • Division of the Z pulse with adjustable ratio 1: 1 to 1: 256
    • External HTL signals for various functions
    • Implementation between the two types of representations for the direction of rotation (A / B 90 °, A/B Dir and vice versa, Division possible)
    • Snap-on housing for top-hat rail (acc. EN 60715)
    • Dimension (B x H X T) 22,5 x 102 x 102 mm
    Details

Title

Company reg # : 4359149
VAT Reg #: 860 5449 17

Copyright © 2018 Encoder Technology Ltd. All Rights Reserved.
Go to Top