+44 (0)1903 788287
Filtered (31)

  • CT701-Firmware: Eccentric Material Processing

    Features

    • MC700 is a universal motion controller for 1 to 4 axis, programmable for multiple motion applications by simple download of the corresponding function firmware
    • With the use of Matona's CT701 firmware, this unit provides excellent solutions with all kinds of guillotine cutters and rotary eccentric shears needing a cosine-compensated speed profile during the penetration of the tool
    • Extremely smooth motion  to protect  mechanical solution, by self-optimizing polynomial speed transitions
    • High cutting accuracy, even during line acceleration and at high speeds
    • Programmable cosine-compensated speed profile
    • Special torque control features to master the impact load when cutting hard materials like stainless steel etc.
    • Special profile features to avoid deadlock between tool and material
    • Embedded virtual master axis (selectable)
    • Black-box unit for cabinet mounting
    • Remote control and communication facilities via external operator terminal, serial PC communication, PROFIBUS or optional via CANBUS (MC700/CI) etc.
    Details

  • CT803-Firmware: Rotating Cross Cutters

    Features

    • 2 pulse inputs with format  A, /A, B, /B, Z, /Z [HTL, RS422]
    • With an input frequency of up to 2 MHz
    • 2 control inputs with format  SIN+, SIN-, COS+, COS- [1 Vss] with an input frequency of up to 400 kHz
    • 2 SSI inputs with format  DATA+, DATA-, CLOCK+, CLOCK- up to 25 Bit, with SSI switching frequency of 100 Hz ... 1 MHz
    • 2 scalable 14-bit analog inputs for ±10 V or 0/4 ... 20 mA
    • 4 control inputs for PNP / NPN signals [10 ... 30 VDC]
    • 4 fast interrupt inputs for PNP / NPN signals [10 ... 30 VDC]
    • 1 pulse output with format  A, /A, B, /B, Z, /Z [RS422]
    • 4 control outputs with push-pull characteristic, short-circuit-proof [5 ... 30 VDC]
    • 2 scalable 14-bit analog outputs for ±10 V or 0/4 ... 20 mA
    • Loop time approx. 250 µs
    • Power supply 18 ... 35 VDC
    • Snap-on housing for top-hat rail (according to EN 60715)
    • OnBoard interfaces: Ethernet / IP, RS232 / RS485, USB 2.0, CANopen, Modbus RTU
    • Optional Ethernet interfaces: EtherCAT, Ethernet / IP, Modbus TCP, Powerlink, PROFINET, SERCOS III
    • Optional Fieldbus interfaces (slave): CC-Link, DeviceNet, PROFIBUS
    • Operates with all 4-Q-drive systems, equipped with a standardized drive communication bus (e. g. SERCOS-II). Alternatively, ±10 V setpoint can be used
    • The controllers can be setup by an external operator terminal as well as HMI’s via standardized factory communication bus e.g. PROFINET
    • Setup via Windows operator software (free of charge)
    Details
  • Encoder Technology 25T Through Hollow Shaft Incremental Encoder

    Encoder Technology 25H Blind Hollow Shaft Incremental Encoder

    Features

    • 5mm Opto-ASIC encoder with a low profile (50.8mm)
    • Imperial bore sizes range from 0.625” to 1.125”
    • Metric bore sizes ranging from 6 mm to 28 mm
    • Single replacement solution for 50.8mm to 88.9mm encoders
    • Resolutions to 10,000 PPR, frequencies to 1 MHz
    • Versatile flexible mounting options
    • RoHS compliant
    • Corrosion-Resistant Option
    Details
  • Encoder Technology 58TF Blind Hollow Shaft Encoder

    Encoder Technology 58TF Blind Hollow Shaft Incremental Encoder

    Features

    • 58 mm package available in thru-bore or hollow bore
    • Resolutions from 1 to 65,536 PPR
    • 6 different output types to choose from
    • 32 different waveforms available
    • Standard and Metric Bore Sizes up to 5/8” and 15 mm
    • Several Flexible Mounting Options
    • IP67 Sealing Available
    Details
  • Encoder Technology 755HS Blind Holow Shaft Encoder

    Encoder Technology 755HS Blind Hollow Shaft Incremental Encoder

    Features

    • Miniature size (38.1mm diameter)
    • Up to 30,000 PPR
    • Flex mounting & large hollow bore option (Up to 14mm)
    • High-temperature option
    Details
  • Encoder Technology 760 Through Hollow Shaft Incremental Encoder

    Encoder Technology 760 Blind Hollow Shaft Incremental Encoder

    Features

    • Size 25 / 63.5mm Diameter (Hollow Shaft)
    • Up to 12 Pole Commutation Available
    • Thru Bore and Blind Bore Options
    • Simple, Innovative Flexible Mounting System
    • Incorporates Opto-ASIC Technology
     
    Details
  • Encoder Technology 925 Single Turn Standard Shaft Absoulte Encoder

    Encoder Technology 925 Single Turn Standard Shaft Absolute Encoder

    Features

    • Standard Size 25 package (2.5")
    • Resolutions up to 12-bit (4096 counts)
    • Incorporates Opto-ASIC technology
    • Industrial-grade, heavy-duty housing
    • Optional IP67 seal
    Details
  • Encoder Technology 960 Single Turn Hollow Shaft Absolute Encoder

    Encoder Technology 960 Single Turn Hollow Shaft Absolute Encoder

    Features

    • Low profile—40mm
    • Thru-bore or hollow-bore styles
    • Industrial-grade, heavy-duty housing
    • State-of-the-art Opto-ASIC circuitry
    Details
  • Encoder Technology A58HE1 Through Hollow Shaft Incremental Encoder

    Encoder Technology A58HE1 Blind Hollow Shaft Incremental Encoder

    Features

    • Number of output pulses per revolution 100-108000 ppr
    • Maximum shaft speed 10000 rpm
    • Permissible motion of shaft - axial: ± 0.5 mm- radial: ± 0.05 mm
    • Accuracy (T1-period lines on disc in arc. sec) ± 0.1T1 arc. sec
    • Starting torque at 20°C ≤ 0.025 Nm
    • Rotor moment of inertia < 1.5x10-4 kgm2
    • Protection (housing) (IEC 529) IP64
    • Protection (shaft side) (IEC 529) IP64
    • Maximum weight without cable 0.3 kg
    • Operating temperature -10...+70°C
    • Storage temperature -30...+80°C
    • Maximum humidity (non-condensing) 98%
    • Permissible vibration (55 to 2000 Hz) ≤ 100 m/s²
    • Permissible shock (5 ms) ≤ 1000 m/s²
    Details
  • Encoder Technology MA36H Muti-turn Hollowshaft Encoder

    Encoder Technology MA36H

    Features

    • Standard Size 36mm package (1.42")
    • Durable magnetic technology
    • Multiturn absolute encoder (12-bit/39-bit)
    • SSI and CANopen communications
    • Proven new turns counting technology — no gears or batteries
    Details
  • Encoder Technology MA36S Muti-turn Standard Shaft Encoder

    Encoder Technology MA36S Muti-turn Standard Shaft Absolute Encoder

    Features

    • Standard Size 36mm package (1.42")
    • Durable magnetic technology
    • Multiturn absolute encoder (12-bit/39-bit)
    • SSI and CANopen communications
    • Proven new turns counting technology — no gears or batteries
    Details
  • Encoder Technology MA58H Series Multi Turn Hollowshaft Absolute

    Encoder Technology MA58H Series Multi Turn Hollowshaft Absolute Encoder

    Features

    • Multi-Turn Absolute Encoder (14 Bit/39 Bit)
    • SSI and CANopen Communications
    • 58 mm Diameter
    • Durable Magnetic Technology
    • Proven Turns Counting Technology – No Gears or Batteries
    • Retains Absolute Position After a Power Outage
    Details
  • Encoder Technology SA36H Single Turn Hollow Shaft Encoder

    Encoder Technology SA36H Single Turn Hollow Shaft Absolute Encoder

    Features

    • Standard Size 36mm package
    • Durable magnetic technology
    • Up to 14 bits of single-turn resolution
    • SSI and CANopen communications
    • Proven turns counting technology—no gears or batteries
    • Flex mount eliminates couplings and is ideal for motors or shafts
    Details
  • Encoder Technology SA36S Single Turn Standard Shaft Absolut

    Encoder Technology SA36S Single Turn Standard Shaft Absolute Encoder

    Features

    • Standard size 36 mm package (1.42")
    • Durable magnetic technology
    • Up to 14 bits of single-turn resolution
    • SSI and CANopen communications
    • Proven new turns counting technology — no gears or batteries
    Details
  • Encoder Technology SA58H Single Turn Hollow Shaft Absolute Encoder

    Encoder Technology SA58H Single Turn Hollow Shaft Absolute Encoder

    Features

    • Up to 14 Bits of Single-Turn Resolution
    • SSI and CANopen Communications
    • 58 mm Diameter
    • Durable Magnetic Technology
    • Retains Absolute Position After a Power Outage
    Details
  • Encoder Technology TBX36 Standard Shaft Absolute Encoder

    Encoder Technology TBX36 Single Turn Standard Shaft Absolute Encoders

    Features

    • Robust aluminium or stainless steel housing (wall thicknesses up to 5 mm)
    • Stainless steel shaft and ball bearing - ball bearing with Simmer ring
    • Rotor with shaft and permanent magnet mounted in pre-chamber
    • Sensor circuit consisting of ASIC
    • Hall elements and interface electronics in enclosed main chamber
    • Housing protection type IP 69K additionally cast
    • Electrical connection via cable (open cable ends)
    Details
  • Encoder Technology SA36S Single Turn Standard Shaft Absolut

    Encoder Technology TBX42 Single Turn Standard Shaft Absolute Encoder

    Features

    • Interface: SSI
    • Design: 42mm
    • Housing Material: Aluminium, stainless steel
    • Flange & Shaft: Synchroniser flange
    • Resolution: 4096 steps/360°<)
    • Code type: Binary, Gray (optional)
    • Electrical connection: Cable 1m
    • Electrical and/or mechanical variant: Basic version
    Details

  • Encoder Technology TBX50 Single Turn Standard Shaft Absolute Encoder

    Features

    • Robust aluminium or stainless steel housing (wall thicknesses up to 5 mm)
    • Stainless steel shaft and ball bearing - ball bearing with Simmer ring
    • Rotor with shaft and permanent magnet mounted in pre-chamber
    • Sensor circuit consisting of ASIC
    • Hall elements and interface electronics in enclosed main chamber
    • Housing protection type IP 69K additionally cast
    • Electrical connection via cable (open cable ends)
    Details

  • Motrona BY340: Synchronous Controller for 1 Follower Axis

    Features

    • 2 pulse inputs with format A, B, 90° [HTL] or A, /A, B, /B [RS422]
    • 4 control inputs for HTL / PNP / NPN / Namur signals [10 ... 30 VDC]
    • Input frequency up to 300 kHz
    • 4 fast transistor outputs, push-pull, short-circuit-proof [5 … 30 VDC]
    • 1 scalable 14-bit analog output (±10 V or 0/4 … 20 mA)
    • Loop time approx. 250 µs
    • Power supply 24 VAC and 17 … 40 VDC
    • Compact norm panel housing (according to EN 60715)
    • Top hat rail mounting by using SM300 support brackets (option)
    • Setup via keys or via PC by serial RS232 interface
    • PROFIBUS connection via Motrona gateway PB251
    Details

  • Motrona BY641: Master / Slave Synchronizers with 4 Relays

    Features

    • 2 pulse inputs with format A, B, 90° [HTL] or A, /A, B, /B [RS422]
    • 4 control inputs for HTL / PNP / NPN / Namur signals [10 ... 30 VDC]
    • Input frequency up to 300 kHz
    • 4 fast transistor outputs, push-pull, short-circuit-proof [5 … 30 VDC]
    • 4 potential-free changeover relay outputs
    • 1 scalable 14-bit analog output (±10 V or 0/4 … 20 mA)
    • Loop time approx. 250 µs
    • Power supply 24 VAC and 17 … 40 VDC
    • Compact norm panel housing (according to EN 60715)
    • Top hat rail mounting by using SM600 support brackets (option)
    • Setup via keys or via PC by serial RS232 interface
    • PROFIBUS connection via Motrona gateway PB251
    Details

  • Motrona BY701-Firmware: Synchronization of Drives

    Features

    • MC700 is a universal motion controller for 1 to 4 axes, which can be assigned any motion control functions by loading firmware. Together with the firmware BY701 (see firmware), this controller offers excellent synchronous functions for 1 - 4 axes.
    • The firmware offers all conceivable possibilities for the synchronization of drives, including the influence of phase position and the relative position between the drives and numerous index and print mark functions.
    • Optionally, a "physical master" or the built-in "virtual master axis" with programmable speeds and ramps can be used as the master drive.
    • The number of successive axes can be extended arbitrarily via a cascading output.
    • MC700 controllers can be operated via an external control terminal, serial interface or optional via CANBUS (MC700/CI). PC operator software is included.
    • PROFIBUS connection possible via gateway PB251 (see accessories)
    Details

  • Motrona CT340: Controller for Rotary Cutters

    Features

    • 2 pulse inputs with format A, B, 90° [HTL] or A, /A, B, /B [RS422]
    • 4 control inputs for HTL / PNP / NPN / Namur signals [10 ... 30 VDC]
    • Input frequency up to 300 kHz
    • 4 fast transistor outputs, push-pull, short-circuit-proof [5 … 30 VDC]
    • 1 scalable 14-bit analog output (±10 V or 0/4 … 20 mA)
    • Loop time approx. 250 µs
    • Cutting length specification via keyboard
    • Power supply 24 VAC and 17 … 40 VDC
    • Compact norm panel housing (according to EN 60715)
    • Top hat rail mounting by using SM300 support brackets (option)
    • Setup via keys or via PC by serial RS232 interface
    • PROFIBUS connection via Motrona gateway PB251
    Details

  • Motrona CT641: Controller with 4 Relays and front-mounted Thumbwheel Switches

    Features

    • 2 pulse inputs with format A, B, 90° [HTL] or A, /A, B, /B [RS422]
    • 4 control inputs for HTL / PNP / NPN / Namur signals [10 ... 30 VDC]
    • Input frequency up to 300 kHz
    • 4 fast transistor outputs, push-pull, short-circuit-proof [5 … 30 VDC]
    • 4 potential-free changeover relay outputs
    • 1 scalable 14-bit analog output (±10 V or 0/4 … 20 mA)
    • Loop time approx. 250 µs
    • Cutting length specification via BCD decade switch on the front
    • Power supply 24 VAC and 17 … 40 VDC
    • Compact norm panel housing (according to EN 60715)
    • Top hat rail mounting by using SM600 support brackets (option)
    • Setup via keys or via PC by serial RS232 interface
    • PROFIBUS connection via Motrona gateway PB251
    Details

  • Motrona FS340: Controller for Flying Saws and Shears

    Features

    • 2 pulse inputs with format A, B, 90° [HTL] or A, /A, B, /B [RS422]
    • 4 control inputs for HTL / PNP / NPN / Namur signals [10 ... 30 VDC]
    • Input frequency up to 300 kHz
    • 4 fast transistor outputs, push-pull, short-circuit-proof [5 … 30 VDC]
    • 1 scalable 14-bit analog output (±10 V or 0/4 … 20 mA)
    • Cutting length specification via keyboard
    • Power supply 24 VAC and 17 … 40 VDC
    • Compact norm panel housing (according to EN 60715)
    • Top hat rail mounting by using SM300 support brackets (option)
    • Setup via keys or via PC by serial RS232 interface
    • PROFIBUS connection via Motrona gateway PB251
    Details

  • Motrona FS641: Controller for Machining “On the Fly”

    Features

    • 2 pulse inputs with format A, B, 90° [HTL] or A, /A, B, /B [RS422]
    • 4 control inputs for HTL / PNP / NPN / Namur signals [10 ... 30 VDC]
    • Input frequency up to 300 kHz
    • 4 fast transistor outputs, push-pull, short-circuit-proof [5 … 30 VDC]
    • 4 potential-free changeover relay outputs
    • 1 scalable 14-bit analog output (±10 V or 0/4 … 20 mA)
    • Cutting length specification via keyboard or front BCD decade switch
    • Power supply 24 VAC and 17 … 40 VDC
    • Compact norm panel housing (according to EN 60715)
    • Top hat rail mounting by using SM600 support brackets (option)
    • Setup via keys or via PC by serial RS232 interface
    • PROFIBUS connection via Motrona gateway PB251
    Details

Title

Company reg # : 4359149
VAT Reg #: 860 5449 17

Copyright © 2018 Encoder Technology Ltd. All Rights Reserved.
Go to Top